Slicone sealants for sealing joints in vinyl floors

Verschiedene Farben (bunt)
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Verschiedene Farben (RAL)
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Verschiedene Farben (bunt)
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Verschiedene Farben (RAL)
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*

Joints in vinyl flooring are not only unattractive to look at, but sometimes also carry the risk of permanent damage. In the following, you will learn what you should therefore already consider when laying vinyl flooring and what you can do if joints in the vinyl floor open up.

What causes joints in the vinyl floor to fall apart

Like many floor coverings, a vinyl floor reacts to different room conditions.

The material works – joints are created or dissolved.

In most cases the reasons for joints in the vinyl floor are either heat or moisture.

Heat

While parquet and laminate floors are primarily sensitive to moisture, vinyl floors primarily react to heat.

The material expands strongly when the heat is affected and reassembles when the temperature drops. The result is diverging joints.

Especially often joints are created in the vinyl floor in rooms with large windows or direct light. The sun’s irradiation leads to a sharp increase in the temperature on the surface – and consequently to the expansion of the vinyl floor.

With darker soils this effect is even more obvious than with brighter soils, as these reflect sunlight better.

But even with underfloor heating systems, the vinyl floor >/g> expands more, which is why it is essential to ensure that the surface is not heated too quickly or too highly.

Moisture

Incoming moisture and subsequent drying also cause joints to rise in the vinyl floor.

Especially in rooms with high humidity or direct contact with water (e.g. B. with vinyl flooring in the bathroom) this can cause permanent damage or mould growth.

Which avoids joints in the vinyl floor

Due to its material properties, the vinyl floor needs sufficient leeway to work.

Therefore, it is important to insert a expansion joint at the time of installation. This applies wherever the vinyl floor meets immovable components (e.g. walls, pipes, columns, built-in furniture) or other floor coverings.

This expansion joint serves to compensate for the elongation and pulling of the material and to allow joints to diverge only where it is intended.

The rule of thumb for the edge distance is at least 5 mm or, in large rooms, 1 mm per metre of length.

Vinyl floor gets joints – what to do?

There are several ways to close joints in the vinyl floor. Various products are available from specialist retailers to fill, glue or seal joints.

Elastic materials – e.g. silicone – are best suited to fill joints in the vinyl floor. They remain permanently flexible, which allows the soil to expand accordingly and contract again.

Corresponding joint fillers are available in numerous different colours and compositions. Therefore, they are versatile and are ideal for closing joints in the edge area.

Verschiedene Farben (bunt)
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Verschiedene Farben (RAL)
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Verschiedene Farben (bunt)
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Build With Colour Ral 1023 Gelb Silikon Dichtmasse*
Verschiedene Farben (RAL)
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*
Ramsauer 450 1K Silikon Dichtstoff 310ml Kartusche (Hellgrau)*

It can also be used to seal transitions to connection joints in doors, skirting boards or stairs.

Sealing joints waterproof is particularly important for vinyl floors in wet rooms to prevent moisture from entering.

Massively laid vinyl can be easily sealed with silicone, e.g. in the edges and connections to tiles, but this is not recommended for floating floors.

Letzte Aktualisierung am 2021-01-16 / Affiliate Links / Bilder von der Amazon Product Advertising API

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply